Showing posts with label system. Show all posts
Showing posts with label system. Show all posts

Thursday, September 26, 2013

Download Navigation System 2011 Chevrolet Equinox And GMC Terrain

2011 Chevrolet Equinox And GMC Terrain
The information in this manual supplements the owner manual. This manual describes features that may or may not be on your specific vehicle either because they are options that you did not purchase or due to changes subsequent to the printing of this owner manual. Please refer to the purchase documentation relating to your specific vehicle to confirm each of the features found on your vehicle. For vehicles first sold in Canada, substitute the name “General Motors of Canada Limited” for Chevrolet and GMC Motor Divisions wherever it appears in this manual. download here
Continue reading...

Tuesday, September 10, 2013

Open Source Solar Data Acquisition System

O.S.S.D.A.S v1 stands for Open Source Solar Data Acquisition System. I have been working on this project since last few months. The picture below is the not the first prototype, but the first working prototype that looks like quite complete. There will be further revisions to the hardware and software for best efficiency and accurate results. Moreover, the recorded digital data should be rich enough to reflect the real world data’s mirror.

Open Source Solar Data Acquisition System
Continue reading...

Wednesday, June 5, 2013

Kenwood Dv3100 Navigation System Wiring Harness Diagram

Wire Diagram on Find More Information About 1947 Harley Davidson Wiring Diagram Here
Find More Information About 1947 Harley Davidson Wiring Diagram Here.


Wire Diagram on Honda Accord Coupe   94 Fan Controls Circuit And Wiring Diagram
Honda Accord Coupe 94 Fan Controls Circuit And Wiring Diagram.


Wire Diagram on Kenwood Kna Dv3100 Dvd Navigation System Wiring Harness Diagram
Kenwood Kna Dv3100 Dvd Navigation System Wiring Harness Diagram.


Wire Diagram on Ktm 250 525 Sx  Mxc  Exc Electrical System And Wiring Diagram
Ktm 250 525 Sx Mxc Exc Electrical System And Wiring Diagram.


Wire Diagram on Wire  The Smaller The Gauge Number The Larger The Conductor Size
Wire The Smaller The Gauge Number The Larger The Conductor Size.


Wire Diagram on Jeep Grand Cherokee Radio Adaptor Wiring Harness   Circuit Schematic
Jeep Grand Cherokee Radio Adaptor Wiring Harness Circuit Schematic.


Wire Diagram on Wiring Diagram Here   Page 1 And Page 2     Source  Autolib Diakom
Wiring Diagram Here Page 1 And Page 2 Source Autolib Diakom.


Wire Diagram on The Following Schematic Shows A Typical Diagram Schematic Of Polaris
The Following Schematic Shows A Typical Diagram Schematic Of Polaris.


Wire Diagram on System And Wiring Diagram Here  60 Pages Of Pdf File Docs
System And Wiring Diagram Here 60 Pages Of Pdf File Docs.


Wire Diagram on Cassette   Cd And 6 Speakers Audio System Wiring   Circuit Schematic
Cassette Cd And 6 Speakers Audio System Wiring Circuit Schematic.


Continue reading...

Wednesday, May 15, 2013

Electrical power System

Electrical System schematic

Electrical power is supplied by a 12 volt, direct current system. The system includes a
12 volt 45 ampere alternator, regulator and 35 ampere hour battery to produce electrical power.
The battery is located in a sealed box aft of the baggage compartment. On the right side of the
fuselage near the battery is an external power receptacle enabling the use of an automotive
battery or external battery charger assist for starting or charging. The aircraft Master
Switch must be on for the external power relay to be energized to provide power to the aircraft
battery and electrical system.
A dual volt / amp meter indicates system performance.

The gauge is designed so that
normal operation is indicated with both needles at or above level. Charging is indicated by a
positive ammeter reading and a voltage between 13 and 14.5 volts.
The split BAT / ALT Master switch "BAT" side energizes the master solenoid to provide
power to the main bus and lower row of circuit breakers. The "ALT" side of the switch energizes
the alternator field turning the alternator on to enable it to recharge the battery. The AVIONICS
MASTER switch / circuit breaker energizes the upper row of circuit breakers providing power to
the avionics. This switch is normally off for engine start.

The engine starter solenoid is
located near the base of the copilots control stick and is activated by the magneto key switch.
The circuit breakers automatically break the electrical circuit if an overload should
occur. To reset the circuit breaker simply push in the reset button. It may be necessary to
allow approximately two minutes for cooling before resetting a circuit breaker.

Corrective
action should be taken in the event of continual circuit breaker popping or a circuit breaker
that will not stay reset. It is possible to manually trip a breaker by pulling out on the reset
Electrical System Schematic
Current schematic with alternator
Continue reading...

Saturday, April 13, 2013

5 Zone Alarm System

This is an entire alarm system with 5 impartial zones appropriate for a small place of business or home environment. It uses just 3 CMOS ICs and includes a timed entry / exit zone, 4 fast zones and a panic howeverton. There are indicators for each zone a \"system armed\" indicator. The schematic is as practices:


\"5


Circuit Notes
Each zone makes use of a generally closed contact. These can be micro changees or usual alarm contacts (usually reed switches). Suitable switches can also be bought from alarm shops and hid in door bodys, or window ledges.

Zone 1 is a timed zone which need to be used because the entry and exit point of the constructing. Zones 2 - 5 are fast zones, for you to trigger the alarm with out a delay. Some RF immunity is presentd for lengthy wiring runs by the input capacitors, C1-C5. C7 and R14 also kind a transient suppressor. The key change acts as the Set/Unset and Reset change. For just right security this must be the metallic kind with a key.

Operation
At change on, C6 will cost by approach of R11, this acts because the exit extend and that is set to round 30 2nds. This may also be altered through varying either C6 or R11. Once the timing length has elapsed, LED6 will mild, which implys the device is armed. LED6 could additionally be installed externally (at the bell box for example) and provides visual indication that the device has set. Once set any contact that opens will set off the alarm, including Zone 1. To stop set offing the alarm on entry to the constructing, the concealed re-entry change need to be functiond. This will discharge C6 and begin the entry timer. The re-entry change can be a hid reed swap, positioned anywhere in a door frame, however invisible to the attention. The panic swap, when pressed, will trigger the alarm when set. Relay contacts RLA1 provide the latch, RLA2 operate the siren or buzzer.


Author : Andy Collinson
Continue reading...

Wednesday, April 10, 2013

Electronic Security System

This reliable and easy-to-operate electronic security system can be used in banks, factories, commercial establishments, houses, etc. The system comprises a monitoring system and several sensing zones. Each sensing zone is provided with a closed-loop switch known as sense switch. Sense switches are fixed onthedoors of premises under security and connected to the monitoring system. As long as the doors are closed, sense switches are also closed. The monitoring system can be installed at a convenient central place for easy operation.

Fig. 1 shows the monitoring circuit only for zone 1 along with the common alarm circuit. For other zones, the monitoring circuit is identical, with only the prefixes of components changing as per zone number. Encircled points A, B, and C of each zone monitoring circuit need to be joined to the corresponding points of the alarm circuit (upper half of Fig. 1).

Fig. 1: Monitoring Circuit Along with the Alarm Circuit diagram

Monitoring circuit along with the alarm circuit

When zone 1 sensing switch S11, zone switch S1 are all on, pnp transistor T12 reverse biases to go in cut-off condition, with its collector at around 0 volt. When the door fitted with sensor switch S11 is opened, transistor T12 gets forward biased and it conducts. Its collector voltage goes high, which forward biases transistor T10 via resistor R10 to turn it on. (Capacitor C10 serves as a filter capacitor.) As a result, the collector voltage of transistor T10 falls to forward bias transistor T11, which conducts and its collector voltage is sustained at a high level. Under this latched condition, sensor switch S11 and the state of transistor T12 have no effect. In this state, red LED11 of the zone remains lit.

Simultaneously, the high-level voltage from the collector of transistor T11 via diode D10 is applied to VDD pin 5 of siren sound generator IC1 (UM3561) whose pin 2 is grounded. Resistor R3 connected across pins 7 and 8 of IC1 determines the frequency of the in-built oscillator. As a result, IC1 starts generating the audio signal output at pin 3. The output voltage from IC1 is further amplified by Darlington pair of transistors T1 and T2. The amplified output of the Darlington pair drives the loudspeaker whose output volume can be controlled by potentiometer VR1. Capacitor C1 serves as a filter capacitor.

Fig. 2: Physical Layout of Sensors and Monitoring Alarm System:

Physical layout of sensors and monitoring alarm system

You can alter the alarm sound as desired by changing the connections of IC1 as shown in the table.

F99_table

The circuit continues to sound the alarm until zone door is closed (to close switch S11) and the reset switch is pressed momentarily (which causes transistor T10 to cut off, returning the circuit to its initial state). The system operates off a 3V DC battery or recharging battery with charging circuit or battery eliminator. If desired, more operating zones can be added. Initially keep the monitoring system switch S1 off. Keep all the zone doors fixed with sensing switches S11, S21, S31, S41, etc closed. This keeps the sensing switches for respective zones in closed position. Also keep zone slide switches S12, S22, S32, S42, etc in ‘on’ position.

This puts the system in operation, guarding all the zone doors.Now, if the door of a particular zone is opened, the monitoring system sounds an audible alarm and the LED corresponding to the zone glows to indicate that the door of the zone is open. The alarm and the LED indication will continue even after that particular door with the sensing switch is immediately closed, or even if that switch is removed/damaged or connecting wire is cut open. Any particular zone in the monitoring system can be put to operation or out of operation by switching on or switching off the corresponding slide switch in the monitoring system.

Source : http://www.ecircuitslab.com/2012/05/electronic-security-system.html
Continue reading...

Thursday, April 4, 2013

iPod and the Auto Sound System

The iPod story seems to be that of a charmed life. If you havent taken a look around there are all kinds of devices and accessories that are created in order to use right along with the wildly popular and successful iPod product offered by Apple. In fact, I cant think of a better coup for Apple to have pulled off against the giant PC industry, even Microsofts new product the Zune is having a great deal of difficulty even catching up to the sales that iPod seems to have no trouble garnering. The success is something that may define explanation but could have a great deal to do with the equally popular accessories and adornments that are made for each and every iPod product.


iPod and the Auto Sound SystemYou might be wondering exactly what this has to do with auto sound systems but those are just another of the many great iPod accessories that can be found in the market place of today. Seriously! Even some car manufacturers are having upgrades that include iPod adapters that allow drivers to play music from their iPods through the tuning device on their auto sound systems. It almost seems too good to be true when you consider that you will not have to risk life and limb by fiddling with your iPod device when looking for that one obscure song somewhere on your list. There are other car stereo makers that have devices and adapters that read and play music from the iPod but you must use the actual iPod to make your selections and any changes. At any rate, when carmakers and stereo manufacturers such as Pioneer and Alpine are creating stereos that have the iPod in mind you can rest assured that it is a cultural phenomenon and not some fluke to be taken lightly.


In addition to auto sound systems you will find iDogs, iPets, iPod covers, iPod players (speakers and docking stations that you plug your iPod into in order to play without the headphones), iPod alarm clocks, and my personal favorite iBaby (this is a stroller made by Kolcraft that has an iPod, speakers, and adapter built in so that baby can hear his or her favorite tunes while being strolled about the town), or the iCrib (another nifty iPod device designed to keep baby pacified-hopefully this nifty gadgets are drool proof). Needless to say there are times in life when its all about the accessories and I have yet seen another maker of MP3 type devices hold a torch to iPod when it comes to offering options for buyers to personalize their music makers.


If you are in the market for an auto sound system, chances are that you either already have an iPod or are seriously not opposed to the idea of owning one. If you either or both are in your near future I highly recommend you consider purchasing an auto sound system that will be completely compatible with your iPod system or any other MP3 type player you choose to use. I do believe however, that you will find better options designed with the iPod in mind as none of the other brands (thus far) have nearly the buyer base and purchasing power of iPod owners. No matter how you feel about it, all indications are that iPods are here to stay and you may as well jump on board when it comes to your auto sound system as well.

Continue reading...

Motorcycle Electrical System Components Sound

Basic Electrical Wiring on Basic Electrical Wiring  Edward L  Safford  Amazon Com  Books
Basic Electrical Wiring Edward L Safford Amazon Com Books.


Basic Electrical Wiring on Speaking Of 3 Wire Cable  Romex 12 3 Has A Black Wire For Hot  A Red
Speaking Of 3 Wire Cable Romex 12 3 Has A Black Wire For Hot A Red.


Basic Electrical Wiring on Basic Electrical Wiring    About Steve
Basic Electrical Wiring About Steve.


Basic Electrical Wiring on Wiring Diagram
Wiring Diagram.


Basic Electrical Wiring on Basic Electric Guitar Circuits Part 1 Pickups Basic Electric Guitar
Basic Electric Guitar Circuits Part 1 Pickups Basic Electric Guitar.


Basic Electrical Wiring on Light Switch Diagram  Power Into Light     Pdf  44kb
Light Switch Diagram Power Into Light Pdf 44kb.


Basic Electrical Wiring on Basic Electrical Wiring   Basic Electrical Wiring Project Beginner
Basic Electrical Wiring Basic Electrical Wiring Project Beginner.


Basic Electrical Wiring on Electrical Wiring   Let S Talk Basic Residential Wiring
Electrical Wiring Let S Talk Basic Residential Wiring.


Basic Electrical Wiring on Wiring Diagram Template Contains Additional Symbols And Graphics
Wiring Diagram Template Contains Additional Symbols And Graphics.


Basic Electrical Wiring on The Motorcycle Electrical System And Components Sound And Appear Very
The Motorcycle Electrical System And Components Sound And Appear Very.


Continue reading...

Wednesday, April 3, 2013

1996 Nissan Quest Wiring Diagram Electrical System Troubleshooting

Wire Diagram on Coupe   94 Fan Controls Circuit And Wiring Diagram   Circuit Schematic
Coupe 94 Fan Controls Circuit And Wiring Diagram Circuit Schematic.


Wire Diagram on Peugeot 405 Wiring Diagram     Starting And Charging System   Circuit
Peugeot 405 Wiring Diagram Starting And Charging System Circuit.


Wire Diagram on Find More Information About Volvo Wiring Diagram S60 S60r S80 2004
Find More Information About Volvo Wiring Diagram S60 S60r S80 2004.


Wire Diagram on Pontiac Fiero Headrest Speakers Wiring Diagram   There Are Two Wiring
Pontiac Fiero Headrest Speakers Wiring Diagram There Are Two Wiring.


Wire Diagram on 940 Electrical System And Wiring Diagram 1994   Circuit Schematic
940 Electrical System And Wiring Diagram 1994 Circuit Schematic.


Wire Diagram on 1996 Nissan Quest Wiring Diagram Electrical System Troubleshooting
1996 Nissan Quest Wiring Diagram Electrical System Troubleshooting.


Wire Diagram on 1988 Bmw 325i E30 Series Wiring Diagrams   Circuit Schematic
1988 Bmw 325i E30 Series Wiring Diagrams Circuit Schematic.


Wire Diagram on Chevrolet Tahoe   Blazer Electrical Wiring Diagram   Circuit Schematic
Chevrolet Tahoe Blazer Electrical Wiring Diagram Circuit Schematic.


Wire Diagram on Wiring Diagram Here     Free Download Pdf File   Source  Mediafire
Wiring Diagram Here Free Download Pdf File Source Mediafire.


Wire Diagram on Infiniti Wiring Diagram Wiring Harness
Infiniti Wiring Diagram Wiring Harness.


Continue reading...